Pretražite po imenu i prezimenu autora, mentora, urednika, prevoditelja

Napredna pretraga

Pregled bibliografske jedinice broj: 471301

Influence of Various Concentrates on Quality of Printing Plates' Wetting Process


Cigula, Tomislav; Gojo, Miroslav; Novaković, Dragoljub; Pavlović Živko
Influence of Various Concentrates on Quality of Printing Plates' Wetting Process // Machine Design (Novi Sad), 49 (2010), 325-330 (podatak o recenziji nije dostupan, članak, znanstveni)


CROSBI ID: 471301 Za ispravke kontaktirajte CROSBI podršku putem web obrasca

Naslov
Influence of Various Concentrates on Quality of Printing Plates' Wetting Process

Autori
Cigula, Tomislav ; Gojo, Miroslav ; Novaković, Dragoljub ; Pavlović Živko

Izvornik
Machine Design (Novi Sad) (1821-1259) 49 (2010); 325-330

Vrsta, podvrsta i kategorija rada
Radovi u časopisima, članak, znanstveni

Ključne riječi
Electrical conductivity; contact angle; fountain solution; lithographic printing plate; pH value; Surface Active Substances (SAS).

Sažetak
One of many elements that influence reproduction quality in lithography is the wetting process of nonprinting areas of the printing plate. Results of investigation of physical-chemical properties of various fountain solutions and influence of various buffer solutions on the wetting process were presented in this paper. Fountain solutions used to conduct investigation were made from demineralised water in which surface active substance, agent for increasing electrical conductivity and buffer solution were added. Main point of this research was to determine optimal volume concentration of surface active substance in dependence of used buffer solution. The results showed that increase of the amount of surface active substances causes decrease of electrical conductivity, but this decrease is dependent on used buffer solution. On the other hand, increase of surface active substance’s volume concentration cause increase of solution’s pH value, but this increase is not significant. Results of the contact angle measurement showed similar behaviour of Samples 1 and 3, reaching low point at nearly 11 percent volume concentration of surface active substance. A bit surprising is the fact that further increase of surface active substance‘s volume concentration causes increase of the contact angle. In conclusion, results showed that used buffer solution don’t have high impact on wetting process of lithographic printing plates, but further investigations should be conducted to determine how investigated sampled influence on surface properties of nonprinting areas of printing plate.

Izvorni jezik
Engleski

Znanstvena područja
Grafička tehnologija



POVEZANOST RADA


Projekti:
128-1201785-2228 - Razvoj metoda mjerenja površina tiskovnih formi (Gojo, Miroslav, MZOS ) ( CroRIS)
128-1281957-1958 - Digitalizacija muzejske slikarske baštine (Agić, Darko, MZOS ) ( CroRIS)

Ustanove:
Grafički fakultet, Zagreb

Profili:

Avatar Url Tomislav Cigula (autor)

Avatar Url Miroslav Gojo (autor)


Citiraj ovu publikaciju:

Cigula, Tomislav; Gojo, Miroslav; Novaković, Dragoljub; Pavlović Živko
Influence of Various Concentrates on Quality of Printing Plates' Wetting Process // Machine Design (Novi Sad), 49 (2010), 325-330 (podatak o recenziji nije dostupan, članak, znanstveni)
Cigula, T., Gojo, M., Novaković, D. & Pavlović Živko (2010) Influence of Various Concentrates on Quality of Printing Plates' Wetting Process. Machine Design (Novi Sad), 49, 325-330.
@article{article, author = {Cigula, Tomislav and Gojo, Miroslav and Novakovi\'{c}, Dragoljub}, year = {2010}, pages = {325-330}, keywords = {Electrical conductivity, contact angle, fountain solution, lithographic printing plate, pH value, Surface Active Substances (SAS).}, journal = {Machine Design (Novi Sad)}, volume = {49}, issn = {1821-1259}, title = {Influence of Various Concentrates on Quality of Printing Plates' Wetting Process}, keyword = {Electrical conductivity, contact angle, fountain solution, lithographic printing plate, pH value, Surface Active Substances (SAS).} }
@article{article, author = {Cigula, Tomislav and Gojo, Miroslav and Novakovi\'{c}, Dragoljub}, year = {2010}, pages = {325-330}, keywords = {Electrical conductivity, contact angle, fountain solution, lithographic printing plate, pH value, Surface Active Substances (SAS).}, journal = {Machine Design (Novi Sad)}, volume = {49}, issn = {1821-1259}, title = {Influence of Various Concentrates on Quality of Printing Plates' Wetting Process}, keyword = {Electrical conductivity, contact angle, fountain solution, lithographic printing plate, pH value, Surface Active Substances (SAS).} }

Uključenost u ostale bibliografske baze podataka::


  • IndexCopernicus





Contrast
Increase Font
Decrease Font
Dyslexic Font