Pretražite po imenu i prezimenu autora, mentora, urednika, prevoditelja

Napredna pretraga

Pregled bibliografske jedinice broj: 1044230

Numerical calculation and experimental measurement of temperatures and welding residual stresses in a thick‑walled T‑joint structure


Perić, Mato; Nižetić, Sandro; Garašić, Ivica; Gubeljak, N enad; Vuherer, Tomaž; Tonković, Zdenko
Numerical calculation and experimental measurement of temperatures and welding residual stresses in a thick‑walled T‑joint structure // Journal of thermal analysis and calorimetry, 140 (2020), 1; 1-10 doi:10.1007/s10973-019-09231-3 (međunarodna recenzija, članak, znanstveni)


CROSBI ID: 1044230 Za ispravke kontaktirajte CROSBI podršku putem web obrasca

Naslov
Numerical calculation and experimental measurement of temperatures and welding residual stresses in a thick‑walled T‑joint structure

Autori
Perić, Mato ; Nižetić, Sandro ; Garašić, Ivica ; Gubeljak, N enad ; Vuherer, Tomaž ; Tonković, Zdenko

Izvornik
Journal of thermal analysis and calorimetry (1388-6150) 140 (2020), 1; 1-10

Vrsta, podvrsta i kategorija rada
Radovi u časopisima, članak, znanstveni

Ključne riječi
Buried-arc welding ; T-joint fillet weld ; Thermocouples ; Residual stresses ; X-ray diffraction ; Hole-drilling

Sažetak
In this investigation, a T-joint numerical welding simulation of thick steel plates is performed to estimate transient temperature distributions, residual stress feld and model defections. A sequential simulation method is applied in the numerical simulation, where the thermal analysis is done by using the EBD technique to simulate the weld wire melting and metal fller addition while the mechanical analysis is performed in one step without EBD to shorten the calculation time. Thermocouples, non- destructive X-ray difraction and semi- destructive hole-drilling methods are used to measure the temperature and residual stress distributions. In the thermal analysis, a simplifed heat fux is used which causes a relatively large temperature discrepancy in the weld pool area between the numerical and experimental results. The calculated temperature histories outside the weld pool and its vicinity correlate very well with the experimental measurements with an acceptable discrepancy of approximately 4%. The residual stresses are frstly measured on the model surface without electropolishing and then two times after that, at depths of 0.005 and 0.015 mm. The results of residual stress obtained by numerical modelling and measurement with X-ray agree better when the electropolishing removing layer is set to 0.015 mm, due to a significantly smaller effect of surface conditions that originate from steel plate production.

Izvorni jezik
Engleski

Znanstvena područja
Strojarstvo, Temeljne tehničke znanosti



POVEZANOST RADA


Ustanove:
Fakultet elektrotehnike, strojarstva i brodogradnje, Split,
Fakultet strojarstva i brodogradnje, Zagreb

Profili:

Avatar Url Mato Perić (autor)

Avatar Url Ivica Garašić (autor)

Avatar Url Sandro Nižetić (autor)

Avatar Url Zdenko Tonković (autor)

Poveznice na cjeloviti tekst rada:

doi

Citiraj ovu publikaciju:

Perić, Mato; Nižetić, Sandro; Garašić, Ivica; Gubeljak, N enad; Vuherer, Tomaž; Tonković, Zdenko
Numerical calculation and experimental measurement of temperatures and welding residual stresses in a thick‑walled T‑joint structure // Journal of thermal analysis and calorimetry, 140 (2020), 1; 1-10 doi:10.1007/s10973-019-09231-3 (međunarodna recenzija, članak, znanstveni)
Perić, M., Nižetić, S., Garašić, I., Gubeljak, N., Vuherer, T. & Tonković, Z. (2020) Numerical calculation and experimental measurement of temperatures and welding residual stresses in a thick‑walled T‑joint structure. Journal of thermal analysis and calorimetry, 140 (1), 1-10 doi:10.1007/s10973-019-09231-3.
@article{article, author = {Peri\'{c}, Mato and Ni\v{z}eti\'{c}, Sandro and Gara\v{s}i\'{c}, Ivica and Gubeljak, N enad and Vuherer, Toma\v{z} and Tonkovi\'{c}, Zdenko}, year = {2020}, pages = {1-10}, DOI = {10.1007/s10973-019-09231-3}, keywords = {Buried-arc welding, T-joint fillet weld, Thermocouples, Residual stresses, X-ray diffraction, Hole-drilling}, journal = {Journal of thermal analysis and calorimetry}, doi = {10.1007/s10973-019-09231-3}, volume = {140}, number = {1}, issn = {1388-6150}, title = {Numerical calculation and experimental measurement of temperatures and welding residual stresses in a thick‑walled T‑joint structure}, keyword = {Buried-arc welding, T-joint fillet weld, Thermocouples, Residual stresses, X-ray diffraction, Hole-drilling} }
@article{article, author = {Peri\'{c}, Mato and Ni\v{z}eti\'{c}, Sandro and Gara\v{s}i\'{c}, Ivica and Gubeljak, N enad and Vuherer, Toma\v{z} and Tonkovi\'{c}, Zdenko}, year = {2020}, pages = {1-10}, DOI = {10.1007/s10973-019-09231-3}, keywords = {Buried-arc welding, T-joint fillet weld, Thermocouples, Residual stresses, X-ray diffraction, Hole-drilling}, journal = {Journal of thermal analysis and calorimetry}, doi = {10.1007/s10973-019-09231-3}, volume = {140}, number = {1}, issn = {1388-6150}, title = {Numerical calculation and experimental measurement of temperatures and welding residual stresses in a thick‑walled T‑joint structure}, keyword = {Buried-arc welding, T-joint fillet weld, Thermocouples, Residual stresses, X-ray diffraction, Hole-drilling} }

Časopis indeksira:


  • Current Contents Connect (CCC)
  • Web of Science Core Collection (WoSCC)
    • Science Citation Index Expanded (SCI-EXP)
    • SCI-EXP, SSCI i/ili A&HCI
  • Scopus


Citati:





    Contrast
    Increase Font
    Decrease Font
    Dyslexic Font