Pretražite po imenu i prezimenu autora, mentora, urednika, prevoditelja

Napredna pretraga

Pregled bibliografske jedinice broj: 983735

Influence of steel preheat temperature and molten casting alloy AlSi9Cu3(Fe) impact speed on wear of X38CrMoV5-1 steel in high pressure die casting conditions


Dadić, Zvonimir; Živković, Dražen; Čatipović, Nikša; Marinić-Kragić, Ivo
Influence of steel preheat temperature and molten casting alloy AlSi9Cu3(Fe) impact speed on wear of X38CrMoV5-1 steel in high pressure die casting conditions // Wear, 424-425 (2019), 15-22 doi:10.1016/j.wear.2019.02.008 (međunarodna recenzija, članak, znanstveni)


CROSBI ID: 983735 Za ispravke kontaktirajte CROSBI podršku putem web obrasca

Naslov
Influence of steel preheat temperature and molten casting alloy AlSi9Cu3(Fe) impact speed on wear of X38CrMoV5-1 steel in high pressure die casting conditions

Autori
Dadić, Zvonimir ; Živković, Dražen ; Čatipović, Nikša ; Marinić-Kragić, Ivo

Izvornik
Wear (0043-1648) 424-425 (2019); 15-22

Vrsta, podvrsta i kategorija rada
Radovi u časopisima, članak, znanstveni

Ključne riječi
preheat temperature ; casting alloy impact speed ; wear ; thermal fatigue ; erosion ; high pressure die casting ; ANSYS CFX

Sažetak
This paper is a part of experimental research in the area of high pressure die casting (HPDC) mould wear. Influence of mould preheat temperature and molten aluminium alloy impact speed on total mould wear was researched using novel laboratory die casting testing equipment. Testing parameters were set to simulate HPDC of aluminium alloy AlSi9Cu3(Fe). The specimens were made from X38CrMoV5-1 hot work steel (H11). Experiment was designed using central composite design. Following the experiment design, 13 specimens were heat treated and the surface was modified by “Tenifer” nitrocarburizing. Specimen wear was measured by a Mettler B5 scale (Küsnacht, Switzerland) and shown graphically by 3D scan before and after the experiment ; the 3D scans were overlapped to determine main wear areas. Response surface was acquired. Most influential tribological wear mechanisms were determined by ANSYS CFX 17.2 analysis. It was found that preheat temperature and molten aluminium alloy impact speed directly affects total wear of the mould surface. An increase of preheat temperature decreases total wear, while an increase of molten aluminium alloy impact speed increases total wear. Conditions for minimum and maximum wear were quantified ; most significant wear was observed on sharp edges of nitrided mould material specimens. ANSYS CFX 17.2 hard particle erosion rate simulation suggested erosion occurrence mostly at impact angles perpendicular to the specimen surface. Other ANSYS CFX 17.2 simulation suggested occurrence of cavitation erosion. SEM analysis indicated an occurrence of intermetallic compounds between molten alloy and hot work steel.

Izvorni jezik
Engleski

Znanstvena područja
Strojarstvo



POVEZANOST RADA


Projekti:
IP-2013-11-5371 - Optimiranje i modeliranje termalnih procesa materijala (OMOTPOM) (Smoljan, Božo, HRZZ - 2013-11) ( CroRIS)

Ustanove:
Fakultet elektrotehnike, strojarstva i brodogradnje, Split

Poveznice na cjeloviti tekst rada:

doi www.sciencedirect.com

Citiraj ovu publikaciju:

Dadić, Zvonimir; Živković, Dražen; Čatipović, Nikša; Marinić-Kragić, Ivo
Influence of steel preheat temperature and molten casting alloy AlSi9Cu3(Fe) impact speed on wear of X38CrMoV5-1 steel in high pressure die casting conditions // Wear, 424-425 (2019), 15-22 doi:10.1016/j.wear.2019.02.008 (međunarodna recenzija, članak, znanstveni)
Dadić, Z., Živković, D., Čatipović, N. & Marinić-Kragić, I. (2019) Influence of steel preheat temperature and molten casting alloy AlSi9Cu3(Fe) impact speed on wear of X38CrMoV5-1 steel in high pressure die casting conditions. Wear, 424-425, 15-22 doi:10.1016/j.wear.2019.02.008.
@article{article, author = {Dadi\'{c}, Zvonimir and \v{Z}ivkovi\'{c}, Dra\v{z}en and \v{C}atipovi\'{c}, Nik\v{s}a and Marini\'{c}-Kragi\'{c}, Ivo}, year = {2019}, pages = {15-22}, DOI = {10.1016/j.wear.2019.02.008}, keywords = {preheat temperature, casting alloy impact speed, wear, thermal fatigue, erosion, high pressure die casting, ANSYS CFX}, journal = {Wear}, doi = {10.1016/j.wear.2019.02.008}, volume = {424-425}, issn = {0043-1648}, title = {Influence of steel preheat temperature and molten casting alloy AlSi9Cu3(Fe) impact speed on wear of X38CrMoV5-1 steel in high pressure die casting conditions}, keyword = {preheat temperature, casting alloy impact speed, wear, thermal fatigue, erosion, high pressure die casting, ANSYS CFX} }
@article{article, author = {Dadi\'{c}, Zvonimir and \v{Z}ivkovi\'{c}, Dra\v{z}en and \v{C}atipovi\'{c}, Nik\v{s}a and Marini\'{c}-Kragi\'{c}, Ivo}, year = {2019}, pages = {15-22}, DOI = {10.1016/j.wear.2019.02.008}, keywords = {preheat temperature, casting alloy impact speed, wear, thermal fatigue, erosion, high pressure die casting, ANSYS CFX}, journal = {Wear}, doi = {10.1016/j.wear.2019.02.008}, volume = {424-425}, issn = {0043-1648}, title = {Influence of steel preheat temperature and molten casting alloy AlSi9Cu3(Fe) impact speed on wear of X38CrMoV5-1 steel in high pressure die casting conditions}, keyword = {preheat temperature, casting alloy impact speed, wear, thermal fatigue, erosion, high pressure die casting, ANSYS CFX} }

Časopis indeksira:


  • Current Contents Connect (CCC)
  • Web of Science Core Collection (WoSCC)
    • Science Citation Index Expanded (SCI-EXP)
    • SCI-EXP, SSCI i/ili A&HCI
  • Scopus


Citati:





    Contrast
    Increase Font
    Decrease Font
    Dyslexic Font