Pregled bibliografske jedinice broj: 740538
Influence of various fluoride agents on working properties and surface characteristics of uncoated, rhodium coated and nitrified nickel-titanium orthodontic wires
Influence of various fluoride agents on working properties and surface characteristics of uncoated, rhodium coated and nitrified nickel-titanium orthodontic wires // Acta odontologica scandinavica, 73 (2015), 4; 241-249 doi:10.3109/00016357.2014.980847 (međunarodna recenzija, članak, znanstveni)
CROSBI ID: 740538 Za ispravke kontaktirajte CROSBI podršku putem web obrasca
Naslov
Influence of various fluoride agents on working properties and surface characteristics of uncoated, rhodium coated and nitrified nickel-titanium orthodontic wires
Autori
Katić, Višnja ; Mandić, Vilko ; Ježek, Damir ; Baršić, Gorana ; Špalj, Stjepan
Izvornik
Acta odontologica scandinavica (0001-6357) 73
(2015), 4;
241-249
Vrsta, podvrsta i kategorija rada
Radovi u časopisima, članak, znanstveni
Ključne riječi
corrosion ; orthodontic appliance ; roughness ; chemically induced ; stress ; mechanical
Sažetak
Objective was to analyze the effect of various fluoride formulations in commercially available agents on working properties of various nickel- titanium orthodontic wires. Uncoated (NiTi), rhodium coated (RhNiTi) and nitrified (NNiTi) wires were immersed to dH2O, MiPaste, Elmex and Mirafluor for 1 h. Unloading slope characteristics (average force, bending action of the force and average plateau length) and the percentage of usable constant force during unloading were observed. Surface roughness (Ra) was measured. SEM and EDS were used for observation of the surface. NiTi had decreased loading and unloading elastic modulus (E) and yield strength (YS) after immersion to MIPaste and Mirafluor. The unloading YS decreased in the RhNiTi by the MIPaste. The loading and unloading YS of the NNiTi increased in Elmex and increased average plateau force. RhNiTi showed higher average plateau length and the percentage of useful constant force during unloading in Mirafluor and the average plateau force lowered after immersion to MIPaste. The unloading slope characteristics for NiTi were affected by all three prophylactic agents, mostly by Mirafluor, and produced significantly lower forces during both loading and unloading, similarly to the NNiTi wires. The RhNiTi had the lowest forces during both loading and unloading in MIPaste. All results were at significance ; p < 0.05. Difference in Ra was observed for RhNiTi after immersion to the MI Paste (p < 0.001 ; h2 = 0.761). The NiTi and NNiTi wires lose less working force when combined with Elmex. The RhNiTi improve their working properties with Mirafluor and deteriorate when combined with MiPaste.
Izvorni jezik
Engleski
Znanstvena područja
Dentalna medicina
POVEZANOST RADA
Projekti:
13.06.2.1.53
Ustanove:
Prehrambeno-biotehnološki fakultet, Zagreb,
Medicinski fakultet, Rijeka,
Fakultet strojarstva i brodogradnje, Zagreb,
Fakultet kemijskog inženjerstva i tehnologije, Zagreb
Profili:
Vilko Mandić
(autor)
Višnja Katić
(autor)
Gorana Baršić
(autor)
Stjepan Špalj
(autor)
Damir Ježek
(autor)
Citiraj ovu publikaciju:
Časopis indeksira:
- Current Contents Connect (CCC)
- Web of Science Core Collection (WoSCC)
- Science Citation Index Expanded (SCI-EXP)
- SCI-EXP, SSCI i/ili A&HCI
- Scopus
- MEDLINE