Pretražite po imenu i prezimenu autora, mentora, urednika, prevoditelja

Napredna pretraga

Pregled bibliografske jedinice broj: 835662

Friction in metal forming – the coefficient of friction μ and the factor of friction m


Grizelj, Branko: Bandić, Borko
Friction in metal forming – the coefficient of friction μ and the factor of friction m // 7. Međunarodni skup o prirodnom plinu, toplini i vodi / Raus, Pero (ur.).
Osijek: J. J. Strossmayer Universiti of Osijek and University of Pech, 2016. str. 189-198 (predavanje, međunarodna recenzija, cjeloviti rad (in extenso), znanstveni)


CROSBI ID: 835662 Za ispravke kontaktirajte CROSBI podršku putem web obrasca

Naslov
Friction in metal forming – the coefficient of friction μ and the factor of friction m

Autori
Grizelj, Branko: Bandić, Borko

Vrsta, podvrsta i kategorija rada
Radovi u zbornicima skupova, cjeloviti rad (in extenso), znanstveni

Izvornik
7. Međunarodni skup o prirodnom plinu, toplini i vodi / Raus, Pero - Osijek : J. J. Strossmayer Universiti of Osijek and University of Pech, 2016, 189-198

Skup
Plin 2016.

Mjesto i datum
Osijek, Hrvatska, 28-30. 09.2016

Vrsta sudjelovanja
Predavanje

Vrsta recenzije
Međunarodna recenzija

Ključne riječi
friction; the coefficient of friction; the factor of friction

Sažetak
Abstract Friction is sometimes helpful. For example, high friction on the punch surface helps increase reductions in deep drawing and ironing. In a few instances it has to have at least some small value, as in rolling where it assures entry of the workpiece into the roll gap and helps maintain rolling without skidding of the workpiece. However, in most instances friction is preferably reduced to zero by the introduction of a lubricant. In the vast majority of metalworking processes the workpiece is deformed by means of a contacting die. The pressure required for deformation generates a normal stress to the die surface, and movement of the workpiece relative to the die surface generates a shear stress at the interface. Thus a classical tribological situation arises, with friction at the die-workpiece interface, and with potential for wear of both die and workpiece materials. Mitigation of these effects then calls for the introduction of a lubricant. In contrast to nonmetalworking situations, deformation of theworkpiece results in a sometimes very substantial enlargement of surface areas. Thus new, fresh metal surfaces are exposed, and the lubricant must protect not only the old but also the new surfaces. The success or failure of such lubrication has important consequences on the quality of the issuing product, and also on pressures, forces, energy requirements, and often the very possibility of plastic deformation itself. For these reasons, the field of friction, lubrication, and wear (tribology) in metalworking has been the subject of many investigations.

Izvorni jezik
Engleski

Znanstvena područja
Strojarstvo



POVEZANOST RADA


Projekti:
152-1201787-1478 - CAD/CAM tehnika za modernu izradbu alata za lim od visokočvrstih čelika u 4D (Grizelj, Branko, MZOS ) ( POIROT)

Ustanove:
Strojarski fakultet, Slavonski Brod


Citiraj ovu publikaciju

Grizelj, Branko: Bandić, Borko
Friction in metal forming – the coefficient of friction μ and the factor of friction m // 7. Međunarodni skup o prirodnom plinu, toplini i vodi / Raus, Pero (ur.).
Osijek: J. J. Strossmayer Universiti of Osijek and University of Pech, 2016. str. 189-198 (predavanje, međunarodna recenzija, cjeloviti rad (in extenso), znanstveni)
Grizelj, Branko: Bandić, Borko (2016) Friction in metal forming – the coefficient of friction μ and the factor of friction m. U: Raus, P. (ur.)7. Međunarodni skup o prirodnom plinu, toplini i vodi.
@article{article, editor = {Raus, P.}, year = {2016}, pages = {189-198}, keywords = {friction, the coefficient of friction, the factor of friction}, title = {Friction in metal forming – the coefficient of friction μ and the factor of friction m}, keyword = {friction, the coefficient of friction, the factor of friction}, publisher = {J. J. Strossmayer Universiti of Osijek and University of Pech}, publisherplace = {Osijek, Hrvatska} }
@article{article, editor = {Raus, P.}, year = {2016}, pages = {189-198}, keywords = {friction, the coefficient of friction, the factor of friction}, title = {Friction in metal forming – the coefficient of friction μ and the factor of friction m}, keyword = {friction, the coefficient of friction, the factor of friction}, publisher = {J. J. Strossmayer Universiti of Osijek and University of Pech}, publisherplace = {Osijek, Hrvatska} }




Contrast
Increase Font
Decrease Font
Dyslexic Font