Napredna pretraga

Pregled bibliografske jedinice broj: 805504

Fizikalna svojstva sadrenih zavoja


Antabak, Anko; Barišić, Branimir; Andabak, Matej; Bradić, Lucija; Brajčinovic, Melita; Haramina, Tatjana; Halužan, Damir; Fuchs, Nino; Ćurković, Selena; Luetić, Tomislav et al.
Fizikalna svojstva sadrenih zavoja // Liječnički vjesnik, 137 (2015), 11-12; 372-376 (međunarodna recenzija, članak, znanstveni)


Naslov
Fizikalna svojstva sadrenih zavoja
(Physical properties of plaster bandages)

Autori
Antabak, Anko ; Barišić, Branimir ; Andabak, Matej ; Bradić, Lucija ; Brajčinovic, Melita ; Haramina, Tatjana ; Halužan, Damir ; Fuchs, Nino ; Ćurković, Selena ; Luetić, Tomislav ; Šiško, Jerko ; Prlić, Ivica

Izvornik
Liječnički vjesnik (0024-3477) 137 (2015), 11-12; 372-376

Vrsta, podvrsta i kategorija rada
Radovi u časopisima, članak, znanstveni

Ključne riječi
Kalcium sulfat ; sadreni zavoji ; ispitivanje materijala
(Calcium sulfate ; Casts ; Materials testing ; Surgical)

Sažetak
The physical properties of plaster bandages are a very important factor in achieving the basic functions of immobilization (maintaining bone fragments in the best possible position), which directly affects the speed and quality of fracture healing. This paper compares the differences between the physical properties of plaster bandages (mass, specific weight, drying rate, elasticity and strength) and records the differences in plaster modeling of fast bonding 10 cm wide plaster bandages, from three different manufacturers: Safix plus (Hartmann, Germany), Cellona (Lohman Rauscher, Austria) and Gipsan (Ivo Lola Ribar ltd., Croatia). Plaster tiles from ten layers of plaster, dimension 10 × 10 cm were made. The total number of tiles from each manufacturer was 48. The water temperature of 22 °C was used for the first 24 tiles and 34 °C was used for the remainder. The average specific weight of the original packaging was: Cellona(0.52 g/cm3), Gipsan (0.50 g/cm3), Safix plus (0.38 g/cm3). Three days after plaster tile modeling an average specific weight of the tiles was: Gipsan (1.15 g/cm3), Safix plus (1.00 g/cm3), Cellona (1.10 g/cm3). The average humidity of 50% for Safix plus and Cellona plaster tiles was recorded 18 hours after modeling, while for the Gipsan plaster tiles, this humidity value was seen after 48 hours. On the third day after plaster modeling the average humidity of the plaster tiles was 30% for Gipsan, 24% for Safix and 16%) for Cellona. Cellona plaster tiles made with 34 °C water achieved the highest elasticity (11.75±3.18 MPa), and Gipsan plaster tiles made with 22 °C had the lowest (7.21±0.9 MPa). Cellona plaster tiles made with 34 °C water showed maximum material strength (4390±838 MPa), and Gipsan plaster tiles made with 22 °C water showed the lowest material strength (771±367 MPa). The rigidity and strength of Cellona and Gipsan plaster are higher in tiles made in warmer water, and for Safix plus are higher in tiles made in cooler water. All three types of plaster differentiate in physical properties. The differences in mass and specific weight before and after plaster modeling are minimal. There are greater differences in drying rate, elasticity and strength between the three different plaster materials.

Izvorni jezik
Hrvatski

Znanstvena područja
Fizika, Strojarstvo, Temeljne medicinske znanosti

Napomena
Rad je rezultat zajedničkih istraživanja istraživača Jedinice za dozimetriju zračenja i Jedinice za higijenu okoline Instituta za medicinska istraživanja i medicinu rada (IMI) i Klinike za dječju kirurgiju KBC Zagreb i uz suradnju s kolegama sa Strojarskog fakulteta Sveučilišta u Zagrebu temeljem interno financiranog istraživačkog projekta IMI.



POVEZANOST RADA


Ustanove
Institut za medicinska istraživanja i medicinu rada, Zagreb,
Medicinski fakultet, Zagreb,
Fakultet strojarstva i brodogradnje, Zagreb,
Klinički bolnički centar Zagreb,
Opća bolnica Karlovac

Časopis indeksira:


  • Scopus
  • MEDLINE