Pretražite po imenu i prezimenu autora, mentora, urednika, prevoditelja

Napredna pretraga

Pregled bibliografske jedinice broj: 715035

Sliding wear of TiO2 sol-gel coating


Grilec, Krešimir; Ćurković, Lidija; Majić Renjo, Marijana; Jakovljević, Suzana; Rede, Vera
Sliding wear of TiO2 sol-gel coating // 18th international research/expert conference "Trends in the development of machinery and associated technology" TMT 2014 proceedings / Ehinović, Sabahudin ; Yalcin, Senay ; Vivancos Calvet, Joan (ur.).
Zenica, Bosna i Hercegovina: Faculty of mechanical engineering in Zenica, 2014. str. 421-424 (poster, međunarodna recenzija, cjeloviti rad (in extenso), znanstveni)


CROSBI ID: 715035 Za ispravke kontaktirajte CROSBI podršku putem web obrasca

Naslov
Sliding wear of TiO2 sol-gel coating

Autori
Grilec, Krešimir ; Ćurković, Lidija ; Majić Renjo, Marijana ; Jakovljević, Suzana ; Rede, Vera

Vrsta, podvrsta i kategorija rada
Radovi u zbornicima skupova, cjeloviti rad (in extenso), znanstveni

Izvornik
18th international research/expert conference "Trends in the development of machinery and associated technology" TMT 2014 proceedings / Ehinović, Sabahudin ; Yalcin, Senay ; Vivancos Calvet, Joan - Zenica, Bosna i Hercegovina : Faculty of mechanical engineering in Zenica, 2014, 421-424

Skup
18th international research/expert conference "Trends in the development of machinery and associated technology" TMT 2014

Mjesto i datum
Budimpešta, Mađarska, 10.-12.09.2014

Vrsta sudjelovanja
Poster

Vrsta recenzije
Međunarodna recenzija

Ključne riječi
titanium dioxide; sol-gel; stainless steel; sliding wear

Sažetak
Nanostructured titanium dioxide (TiO2) coatings are interesting due to their good properties, such as high hardness, chemical stability, wear and oxidation resistance, high refractive index, high dielectric constant, good antibacterial and photoelectrochemical properties. In order to improve wear resistance of stainless steel AISI 304 (X5CrNi18-10), ceramics nanostructured TiO2 thin films were deposited on the steel surface by the sol-gel process and dip coating technique. Stainless steel substrates were drawn from the sol at two different rates. After dip coating, the steel substrates were dried, first at room temperature and thereafter at 100 C. In order to increase the coating thickness, the whole process was repeated three times. Subsequently, heat treatment at two different temperatures (400 C and 500 C) was conducted. Prior to sliding test, the thickness and composition of the deposited films were analyzed by Quantitative Depth Profile (QDP) analysis on the Glow Discharge Optical Emission Spectrometer (GDOES). Sliding tests were performed by modified "block on ring" method. Wear scars were analyzed by optical microscope and test results showed the influence of drawing rate during dip coating on the width of wear scars.

Izvorni jezik
Engleski

Znanstvena područja
Kemijsko inženjerstvo, Strojarstvo



POVEZANOST RADA


Ustanove
Fakultet strojarstva i brodogradnje, Zagreb

Citiraj ovu publikaciju

Grilec, Krešimir; Ćurković, Lidija; Majić Renjo, Marijana; Jakovljević, Suzana; Rede, Vera
Sliding wear of TiO2 sol-gel coating // 18th international research/expert conference "Trends in the development of machinery and associated technology" TMT 2014 proceedings / Ehinović, Sabahudin ; Yalcin, Senay ; Vivancos Calvet, Joan (ur.).
Zenica, Bosna i Hercegovina: Faculty of mechanical engineering in Zenica, 2014. str. 421-424 (poster, međunarodna recenzija, cjeloviti rad (in extenso), znanstveni)
Grilec, K., Ćurković, L., Majić Renjo, M., Jakovljević, S. & Rede, V. (2014) Sliding wear of TiO2 sol-gel coating. U: Ehinović, S., Yalcin, S. & Vivancos Calvet, J. (ur.)18th international research/expert conference "Trends in the development of machinery and associated technology" TMT 2014 proceedings.
@article{article, year = {2014}, pages = {421-424}, keywords = {titanium dioxide, sol-gel, stainless steel, sliding wear}, title = {Sliding wear of TiO2 sol-gel coating}, keyword = {titanium dioxide, sol-gel, stainless steel, sliding wear}, publisher = {Faculty of mechanical engineering in Zenica}, publisherplace = {Budimpe\v{s}ta, Ma\djarska} }




Contrast
Increase Font
Decrease Font
Dyslexic Font