Pretražite po imenu i prezimenu autora, mentora, urednika, prevoditelja

Napredna pretraga

Pregled bibliografske jedinice broj: 642446

Effect of machining parameters on jet lagging in abrasive water jet cutting


Marušić, Vlatko; Baralić, Jelena; Nedić, Bogdan; Rosandić, Željko; Budić, Ivan
Effect of machining parameters on jet lagging in abrasive water jet cutting // Tehnički vjesnik, 20 (2013), 4; 677-682 (međunarodna recenzija, članak, znanstveni)


CROSBI ID: 642446 Za ispravke kontaktirajte CROSBI podršku putem web obrasca

Naslov
Effect of machining parameters on jet lagging in abrasive water jet cutting

Autori
Marušić, Vlatko ; Baralić, Jelena ; Nedić, Bogdan ; Rosandić, Željko ; Budić, Ivan

Izvornik
Tehnički vjesnik (1330-3651) 20 (2013), 4; 677-682

Vrsta, podvrsta i kategorija rada
Radovi u časopisima, članak, znanstveni

Ključne riječi
abrasive water jet ; jet lagging ; machining parameters

Sažetak
The main characteristics of the surface machined with the abrasive water jet are the differences in surface roughness at the top and bottom of the cut and the appearance of curved lines-striations, which are characteristic for all machining processes with the concentrated stream of high energy. The curvature of these lines is the consequence of jet lagging. Jet lagging is the cause of errors in cutting of radius and sharp corners. The machining parameters have a great influence on this phenomenon. Therefore, it is necessary to know and to define the influence of machining parameters on this phenomenon. The aim of this paper is to investigate the effect of machining parameters on the jet lagging, i.e. cut front geometry. The specimens of AISI 304 were machined by the abrasive water jet under varying traverse speeds, operating pressures and abrasive mass flow rates. The jet lagging was measured at ten monitoring points by the depth of cut. Based on these results, the relationship between the jet lagging and machining parameters has been formed.

Izvorni jezik
Hrvatski, engleski

Znanstvena područja
Strojarstvo



POVEZANOST RADA


Projekti:
152-1201833-1471 - Utjecaj duplex postupka na strukturu čelika i inženjerstvo površina (Krumes, Dragomir, MZOS ) ( POIROT)
152-1521473-1475 - Povećanje učinkovitosti i kvalitete odljevaka-hrvatske perspektive (Budić, Ivan, MZOS ) ( POIROT)

Ustanove:
Strojarski fakultet, Slavonski Brod

Profili:

Avatar Url Ivan Budić (autor)

Avatar Url Vlatko Marušić (autor)

Avatar Url Željko Rosandić (autor)

Citiraj ovu publikaciju

Marušić, Vlatko; Baralić, Jelena; Nedić, Bogdan; Rosandić, Željko; Budić, Ivan
Effect of machining parameters on jet lagging in abrasive water jet cutting // Tehnički vjesnik, 20 (2013), 4; 677-682 (međunarodna recenzija, članak, znanstveni)
Marušić, V., Baralić, J., Nedić, B., Rosandić, Ž. & Budić, I. (2013) Effect of machining parameters on jet lagging in abrasive water jet cutting. Tehnički vjesnik, 20 (4), 677-682.
@article{article, year = {2013}, pages = {677-682}, keywords = {abrasive water jet, jet lagging, machining parameters}, journal = {Tehni\v{c}ki vjesnik}, volume = {20}, number = {4}, issn = {1330-3651}, title = {Effect of machining parameters on jet lagging in abrasive water jet cutting}, keyword = {abrasive water jet, jet lagging, machining parameters} }
@article{article, year = {2013}, pages = {677-682}, keywords = {abrasive water jet, jet lagging, machining parameters}, journal = {Tehni\v{c}ki vjesnik}, volume = {20}, number = {4}, issn = {1330-3651}, title = {Effect of machining parameters on jet lagging in abrasive water jet cutting}, keyword = {abrasive water jet, jet lagging, machining parameters} }

Časopis indeksira:


  • Web of Science Core Collection (WoSCC)
    • Science Citation Index Expanded (SCI-EXP)
    • SCI-EXP, SSCI i/ili A&HCI
  • Scopus


Uključenost u ostale bibliografske baze podataka:


  • Abstracts in Anthropology





Contrast
Increase Font
Decrease Font
Dyslexic Font