Nalazite se na CroRIS probnoj okolini. Ovdje evidentirani podaci neće biti pohranjeni u Informacijskom sustavu znanosti RH. Ako je ovo greška, CroRIS produkcijskoj okolini moguće je pristupi putem poveznice www.croris.hr
izvor podataka: crosbi

Ispitivanje hrapavosti površine glazirane Y-TZP zubne keramike nakon izlaganja korozivnom mediju (CROSBI ID 193763)

Prilog u časopisu | prethodno priopćenje

Štefančić, Sanja ; Ćurković, Lidija ; Baršić, Gorana ; Majić Renjo, Marijana ; Mehulić, Ketij Investigation of Glazed Y-TZP Dental Ceramics Corrosion by Surface Roughness Measurement / Ispitivanje hrapavosti površine glazirane Y-TZP zubne keramike nakon izlaganja korozivnom mediju // Acta stomatologica Croatica, 47 (2013), 2; 163-168. doi: 10.15644/asc47/2/8

Podaci o odgovornosti

Štefančić, Sanja ; Ćurković, Lidija ; Baršić, Gorana ; Majić Renjo, Marijana ; Mehulić, Ketij

hrvatski

Ispitivanje hrapavosti površine glazirane Y-TZP zubne keramike nakon izlaganja korozivnom mediju

Introduction: Among dental applications, the zirconia based ceramics are widespread because of their general properties. The changes in superficial surface roughness correspond to the structural changes in the material caused by the influence of corrosion. The aim of this study was to determine chemical stability of glazed Y-TZP using surface roughness measurements. Materials and methods: Five samples of Y-TZP material BruxZir (Glidewell Laboratories © 2012.) with the addition of pigment A3 were sintered, polished and glazed to imitate the finishing process in producing monolithic crowns. After determining the mass of the sample, each sample was immersed in 10 ml of 4 wt. % CH3COOH aqueous solution. The roughness was measured five times before and after immersion. Results: All measured roughness parameters have significantly increased, showing higher penetration depth in all surface areas after immersion in 4 wt. % CH3COOH aqueous solution compared to the initial values. Weight loss of investigated dental ceramics samples was 2.45 mg/cm2 ± 0.026. Conclusion: Highly acidic conditions augment surface roughness of Y-TZP glazed dental ceramics.

dental porcelain ; surface properties ; corrosion

nije evidentirano

engleski

Investigation of Glazed Y-TZP Dental Ceramics Corrosion by Surface Roughness Measurement

Introduction: Among dental applications, the zirconia based ceramics are widespread because of their general properties. The changes in superficial surface roughness correspond to the structural changes in the material caused by the influence of corrosion. The aim of this study was to determine chemical stability of glazed Y-TZP using surface roughness measurements. Materials and methods: Five samples of Y-TZP material BruxZir (Glidewell Laboratories © 2012.) with the addition of pigment A3 were sintered, polished and glazed to imitate the finishing process in producing monolithic crowns. After determining the mass of the sample, each sample was immersed in 10 ml of 4 wt. % CH3COOH aqueous solution. The roughness was measured five times before and after immersion. Results: All measured roughness parameters have significantly increased, showing higher penetration depth in all surface areas after immersion in 4 wt. % CH3COOH aqueous solution compared to the initial values. Weight loss of investigated dental ceramics samples was 2.45 mg/cm2 ± 0.026. Conclusion: Highly acidic conditions augment surface roughness of Y-TZP glazed dental ceramics.

dental porcelain ; surface properties ; corrosion

nije evidentirano

nije evidentirano

nije evidentirano

nije evidentirano

nije evidentirano

nije evidentirano

Podaci o izdanju

47 (2)

2013.

163-168

objavljeno

0001-7019

1846-0410

10.15644/asc47/2/8

Povezanost rada

Dentalna medicina, Strojarstvo

Poveznice
Indeksiranost