Pretražite po imenu i prezimenu autora, mentora, urednika, prevoditelja

Napredna pretraga

Pregled bibliografske jedinice broj: 569944

Temperature changes during cortical bone drilling with a newly designed step drill and an internally cooled drill


Augustin, Goran; Davila, Slavko; Udiljak, Toma; Staroveški, Tomislav; Brezak, Danko; Babić, Slaven
Temperature changes during cortical bone drilling with a newly designed step drill and an internally cooled drill // International orthopaedics, 36 (2012), 7; 1449-1456 doi:10.1007/s00264-012-1491-z (međunarodna recenzija, članak, znanstveni)


Naslov
Temperature changes during cortical bone drilling with a newly designed step drill and an internally cooled drill

Autori
Augustin, Goran ; Davila, Slavko ; Udiljak, Toma ; Staroveški, Tomislav ; Brezak, Danko ; Babić, Slaven

Izvornik
International orthopaedics (0341-2695) 36 (2012), 7; 1449-1456

Vrsta, podvrsta i kategorija rada
Radovi u časopisima, članak, znanstveni

Ključne riječi
Cortical bone drilling; Thermal osteonecrosis; Temperature; Step drill; Internally cooled drill

Sažetak
Purpose - Bone drilling causes an increase in bone temperature, and a temperature above 47°C is critical because it causes thermal bone necrosis. Thermal osteonecrosis is common with the drill diameter of ≥4.5 mm without cooling. The aim of this study was to determine the increase of bone temperature during drilling using newly contructed two-step and internally cooled drills. Methods - An experiment was set up according to a central composite design. An internally cooled drill (3.4 mm and 4.5 mm) and a two-step drill (2.5/3.4 and 3.4/4.5 mm) were used in combination with feed rates of (0.02, 0.04, 0.10, 0.16 and 0.18 mm/rev) and cutting speeds (1.18, 10.68, 33.61, 56.55 and 66.05 m/min) with and without cooling with water of 24°C. Bone temperatures were measured with thermocouples. Drilling was performed on pig diaphyses with a three-axis mini milling machine. Results - Bone temperatures in all combinations of parameters with internal cooling were below the critical 47°C (p = 0.05). The highest temperatures were detected using a 4.5-mm drill (40.5°C). A statistically significant effect other than cooling was found with the drill diameter and feed. A drill diameter of 3.4 mm with internal cooling developed a maximum temperature of 38.5°C and without cooling 46.3°C. For the same conditions a drill with diameter of 4.5 mm reached temperatures of 40.5°C and 55.7°C, respectively. The effect of feed rate is inversely proportional to the increase in bone temperature. With the feed rate 0.16 mm/rev, temperature was below critical even using the 4.5-mm drill (46.4°C, p = 0.05). Using the 3.4-mm drill all temperatures were below critical (46.2°C, p = 0.05). The two- step drill compared to a standard drill with the same diameter did not show statistical differences in maximum bone temperatures for all combinations of parameters (p = 0.05). Conclusions - A two-step drill does not have any advantages over a standard twist drill of the same diameter. An internally cooled drill causes a significantly smaller increase of bone temperature during drilling with water of 24°C. An internally cooled drill is currently the 'ideal' drill for traumatology/orthopaedics because it produces the smallest increase in bone drilling temperature. If internal cooling is used the regulation of other drilling parameters is of no importance.

Izvorni jezik
Engleski

Znanstvena područja
Strojarstvo, Kliničke medicinske znanosti



POVEZANOST RADA


Projekt / tema
120-1201948-1938 - Napredni obradni sustavi i procesi (Toma Udiljak, )
120-1201948-1945 - Inteligentno vođenje obradnih sustava (Dubravko Majetić, )
214-0000000-0523 - Termičke promjene kod cijeljenja kostiju nakon prijeloma (Slavko Davila, )

Ustanove
Fakultet strojarstva i brodogradnje, Zagreb,
Klinika za traumatologiju,
Klinički bolnički centar Zagreb

Citiraj ovu publikaciju

Augustin, Goran; Davila, Slavko; Udiljak, Toma; Staroveški, Tomislav; Brezak, Danko; Babić, Slaven
Temperature changes during cortical bone drilling with a newly designed step drill and an internally cooled drill // International orthopaedics, 36 (2012), 7; 1449-1456 doi:10.1007/s00264-012-1491-z (međunarodna recenzija, članak, znanstveni)
Augustin, G., Davila, S., Udiljak, T., Staroveški, T., Brezak, D. & Babić, S. (2012) Temperature changes during cortical bone drilling with a newly designed step drill and an internally cooled drill. International orthopaedics, 36 (7), 1449-1456 doi:10.1007/s00264-012-1491-z.
@article{article, year = {2012}, pages = {1449-1456}, DOI = {10.1007/s00264-012-1491-z}, keywords = {Cortical bone drilling, Thermal osteonecrosis, Temperature, Step drill, Internally cooled drill}, journal = {International orthopaedics}, doi = {10.1007/s00264-012-1491-z}, volume = {36}, number = {7}, issn = {0341-2695}, title = {Temperature changes during cortical bone drilling with a newly designed step drill and an internally cooled drill}, keyword = {Cortical bone drilling, Thermal osteonecrosis, Temperature, Step drill, Internally cooled drill} }

Časopis indeksira:


  • Current Contents Connect (CCC)
  • Web of Science Core Collection (WoSCC)
    • Science Citation Index Expanded (SCI-EXP)
    • SCI-EXP, SSCI i/ili A&HCI
  • Scopus
  • MEDLINE


Uključenost u ostale bibliografske baze podataka:


  • Abstracts in Anthropology
  • EMBASE (Excerpta Medica)
  • MEDLINE


Citati